Arduino_learn的詳細介紹

//Arduino UNO,  using an Arduino Wiznet Ethernet shield, DHT11, I²C 1602 LCD.

 

/*
 using an Arduino Wiznet Ethernet shield.

 Circuit:
 * Ethernet shield attached to pins 10, 11, 12, 13

 */

#include
#include
//PCF8574A地址為0x38~0x3f
LiquidCrystal_I2C lcd(0x3f, 16, 2);  // set the LCD address to 0x27 for a 16 chars and 2 line display

#include
DS1307 RTC;

#include
#include 

// Enter a MAC address for your controller below.
// Newer Ethernet shields have a MAC address printed on a sticker on the shield
byte mac[] = { 0x00, 0xAA, 0xBB, 0xCC, 0xDE, 0x02 };

// Initialize the Ethernet client library
// with the IP address and port of the server
// that you want to connect to (port 80 is default for HTTP):
EthernetClient client;

// fill in an available IP address on your network here,
// for manual configuration:
IPAddress ip(192, 168, 2, 177);
IPAddress gateway(192, 168, 2, 1);
IPAddress subnet(255, 255, 255, 0);
// fill in your Domain Name Server address here:
IPAddress myDns(8, 8, 8, 8);

//const char server[] = "www.embanju.org";
const char server[] = "192.168.2.104";

//IPAddress server(121.42.180.30);
const int port = 8181;

#include
//=============  此處必須修改============
const char APIKEY[] = "hahaha"; // 此處替換為你自己的API KEY
char DEVICEID[] = "1"; // 此處替換為你的設備編號
const char INPUTID1[] = "1";
const char INPUTID2[] = "1";
const char INPUTID3[] = "1";
const char INPUTID4[] = "1";
//=======================================

aJsonStream serial_stream(&client);
unsigned long lastCheckInTime = 0;
unsigned long lastUpdateTime = 0;
const unsigned long postingInterval = 40000; // delay between 2 datapoints, 40s
const unsigned long updateInterval = 5000; // delay between 2 datapoints, 5s
boolean isCheckIn = false;

#include "DHT.h"

#define DHTPIN 9     // what digital pin we're connected to

// Uncomment whatever type you're using!
#define DHTTYPE DHT11   // DHT 11
//#define DHTTYPE DHT22   // DHT 22  (AM2302), AM2321
//#define DHTTYPE DHT21   // DHT 21 (AM2301)

// Connect pin 1 (on the left) of the sensor to +5V
// NOTE: If using a board with 3.3V logic like an Arduino Due connect pin 1
// to 3.3V instead of 5V!
// Connect pin 2 of the sensor to whatever your DHTPIN is
// Connect pin 4 (on the right) of the sensor to GROUND
// Connect a 10K resistor from pin 2 (data) to pin 1 (power) of the sensor

// Initialize DHT sensor.
// Note that older versions of this library took an optional third parameter to
// tweak the timings for faster processors.  This parameter is no longer needed
// as the current DHT reading algorithm adjusts itself to work on faster procs.
DHT dht(DHTPIN, DHTTYPE);
//out to lcd & Serial.
#define OUT(s) do{Serial.print(s);lcd.print(s);}while(0)
#define OUT_ln(s) do{Serial.println(s);lcd.print(s);}while(0)
#define OUT_FMT(s,v) do{Serial.print(s,v);lcd.print(s,v);}while(0)

// This is optional, but set to false to disable
#define LED_DEBUG true
#include

// Set this to override the default value
#define LED_DEBUG_PIN 2

//update values
//同時上傳n個接口數據調用此函數
#define UPDATE_BEGIN(did) do{ client.print(F("{\"M\":\"update\",\"ID\":\"")); client.print(did);\
    client.print(F("\",\"V\":{\""));Serial.print(F("update:"));}while(0)
//repeats as many as you want
#define UPDATE_V(id,value) do{client.print(id); client.print(F("\":\"")); client.print(value); \
        Serial.print(id); Serial.print(F("->")); Serial.print(value); }while(0)
#define UPDATE_V_NEXT() do{client.print(F("\",\""));Serial.print("：");}while(0)

#define UPDATE_END() do{client.println(F("\"}}"));\
    lastCheckInTime = millis(); \
    lastUpdateTime= millis(); \
    Serial.println(); }while(0)

#define sayToClient(client_id, content)  do{ \
      client.print(F("{\"M\":\"say\",\"ID\":\"")); \
      client.print(client_id);  \
      client.print(F("\",\"C\":\""));  \
      client.print(content);    \
      client.println(F("\"}"));    \
      lastCheckInTime = millis();   \
      Serial.print(F("say to ")); Serial.print(client_id); Serial.print(F(":")); \
      Serial.println(content);  }while(0)

void checkIn();

void printTime() {
    DateTime now = RTC.now();
    char buf[26];
    strncpy(buf, "YYYY-MM-DD hh:mm:ss \0", sizeof(buf));
    Serial.print(now.format(buf));
}

void setup() {
    // Open serial communications and wait for port to open:
    Serial.begin(115200);

    // this check is only needed on the Leonardo:
    while (!Serial) {
        ; // wait for serial port to connect. Needed for Leonardo only
    }
    // Set current time only the first to values, hh,mm are needed
    //   Wire.begin();
    lcd.init();                      // initialize the lcd
    // Print a message to the LCD.
    lcd.backlight();
    delay(300);
    lcd.setCursor(1, 0);
    lcd.print(F("Hello, world!"));
    lcd.setCursor(0, 1);

    if (!RTC.isrunning()) {
        OUT(F("RTC is NOT running!\n"));
        // following line sets the RTC to the date & time this sketch was compiled
        RTC.adjust(DateTime(__DATE__, __TIME__));
    }
    printTime();
    Serial.println();
    dht.begin();
    // start the Ethernet connection:
    Serial.println(F("Trying to get an IP address using DHCP"));
    // initialize the ethernet device not using DHCP:
    if (Ethernet.begin(mac) == 0) {
        OUT(F("Failed to configure Ethernet using DHCP\n"));
        // start the Ethernet connection using a fixed IP address and DNS server:
        Ethernet.begin(mac, ip, myDns, gateway, subnet);
    }
    // print your local IP address:
    ip = Ethernet.localIP();
    Serial.print(F("My IP address: "));
    lcd.setCursor(0, 1);
    lcd.print(F("IP:"));
    for (byte thisByte = 0; thisByte < 4; thisByte++) {
        // print the value of each byte of the IP address:
        OUT_FMT(ip[thisByte], DEC);
        OUT(".");
    }
    Serial.println();

    Serial.println(F("Try Connecting..."));
    Serial.println(F("connecting..."));
    if(client.connect(server, port)){
      Serial.println(F("connected"));
      delay(2000);
      checkIn();
    }else{
      Serial.println(F("connection failed"));
    }
}
unsigned long lastConnectionTime = 0;             // last time you connected to the server, in milliseconds
const unsigned long Interval = 1L * 1000L; // delay between updates, in milliseconds
    float h,t;
void loop() {
    // Wait a few seconds between measurements.
//    delay(2000);
    if (millis() - lastCheckInTime > postingInterval) {
        Serial.println(F("checking in"));
        checkIn();
    }

    if (millis() - lastConnectionTime > Interval) {
     // Reading temperature or humidity takes about 250 milliseconds!
    // Sensor readings may also be up to 2 seconds 'old' (its a very slow sensor)
     h = dht.readHumidity();
    // Read temperature as Celsius (the default)
     t = dht.readTemperature();
//    // Read temperature as Fahrenheit (isFahrenheit = true)
//    float f = dht.readTemperature(true);

    // Check if any reads failed and exit early (to try again).
    if (isnan(h) || isnan(t)/* || isnan(f)*/) {
        Serial.println(F("Failed to read from DHT sensor!"));
 //       return;
    }
//    // Compute heat index in Fahrenheit (the default)
//    float hif = dht.computeHeatIndex(f, h);
//    // Compute heat index in Celsius (isFahreheit = false)
//    float hic = dht.computeHeatIndex(t, h, false);
    Serial.print(F("Humidity: "));
    Serial.print(h);
    Serial.print(F(" %\t"));
    Serial.print(F("Temperature: "));
    Serial.print(t);
    Serial.print(F(" *C\n"));
//        Serial.print(f);
//        Serial.print(" *F\t");
//        Serial.print("Heat index: ");
//        Serial.print(hic);
//        Serial.print(" *C ");
//        Serial.print(hif);
//        Serial.println(" *F");

    lcd.setCursor(0, 0);
    lcd.print(F("H:"));
    lcd.print(h);
    lcd.print(F("% T:"));
    lcd.print(t);
    lcd.print(F("*C"));
    lastConnectionTime=millis();
}
    if ((millis() - lastUpdateTime > updateInterval) && isCheckIn) {
        printTime();
         int val;    //定義變量
        int dat;    //定義變量
        dat = analogRead(A1);    // 讀取傳感器的模擬值并賦值給dat
        val = dat * (4.76 / 1023.0 * 100);
        UPDATE_BEGIN(DEVICEID);//上傳接口數據
        UPDATE_V(INPUTID1, val); //V1
        UPDATE_V_NEXT();
        UPDATE_V(INPUTID2, h); //V2
        UPDATE_V_NEXT();
        UPDATE_V(INPUTID3, t); //V3
        UPDATE_V_NEXT();
        UPDATE_V(INPUTID4, digitalRead(8)); //Pin8
        UPDATE_END();
    }

    if (serial_stream.available()) {
        /* First, skip any accidental whitespace like newlines. */
        serial_stream.skip();
    }
    if (serial_stream.available()) {
        /* Something real on input, let's take a look. */
        aJsonObject *msg = aJson.parse(&serial_stream);
        processMessage(msg);
        aJson.deleteItem(msg);
    }
}

void checkIn() {
    if (!client.connected()) {
        Serial.println(F("connection failed"));
        client.stop();
        isCheckIn = false;
        client.connect(server, port);
        Serial.println(F("connecting..."));
        delay(10000);
    } else {
        Serial.println(F("connection success"));
        client.print(F("{\"M\":\"checkin\",\"ID\":\""));
        client.print(DEVICEID);
        client.print(F("\",\"K\":\""));
        client.print(APIKEY);
        client.println(F("\"}"));
        lastCheckInTime = millis();
        Serial.println(F("checking..."));
        PULSE();        // Emits pulses
    }
}

void processMessage(aJsonObject *msg) {
    aJsonObject* method = aJson.getObjectItem(msg, "M");
    aJsonObject* content = aJson.getObjectItem(msg, "C");
    aJsonObject* client_id = aJson.getObjectItem(msg, "ID");
    String M = method->valuestring;

    // Emits multiple pulses
    PULSE(5);
    Serial.println(M);
//    char* st = aJson.print(msg);//注意：大緩沖區PRINT_BUFFER_LEN=256字節
//
//    if (st != NULL) {
//        Serial.println(st);
//        free(st);
        if (M == "checkinok") {
            isCheckIn = true;
            Serial.println(F("check in OK!"));
        }else if(M=="say" ){
            String C=content->valuestring;
            String F_C_ID=client_id->valuestring;
            if(C=="play"){
                PULSE(3, 250);
                sayToClient(F_C_ID,"LED on!");
            }else if(C=="stop"){
                PULSE(3, 100);
                sayToClient(F_C_ID,"LED off!");
            }else{
                sayToClient(F_C_ID,"You say "+C);
            }
        }
//    }
}

 

 

building log:

 

bigiot/learn01/Release/learn01.elf  :
section            size      addr
.data               368   8388864
.text             29444         0
.bss                918   8389232
.comment             17         0
.debug_aranges     6688         0
.debug_info      365660         0
.debug_abbrev     48709         0
.debug_line       42898         0
.debug_frame      25208         0
.debug_str        46477         0
.debug_loc       150009         0
.debug_ranges      8616         0
Total            725012

Finished building